Current Position：Home > Product > High Voltage Insulation Equipm

Product details

TKJFPartial discharge detector

Other name：Portable Partial Discharge Test Equipment Four Channel Partial Discharge Detector

Specification Certificate of identification Service promise

Current limiting protection Power amplifier protection Voltage short circuit protection Open circuit protection Thermal protection of power amplifier

Note:Regarding product purchase, technical maintenance and other services, welcome to send email:

IntroductionParametersAccessoriesService

Product Introduction

TKJF fit for many products it has high sensitivity high S/N a large screen which has clear testing wave displaying high frequency ellipse scan (the power is less than 1VA). auxiliary zero marking system. The discharge meter has pointer/digital display and linearity /digital function. The amplifier has large dynamic range 9 kinds of frequency band combinations.

TKJF is a powerful tool for developing new high voltage electric products and improving the quality of the products. It is also an efficient testing device to judge the work condition of equipments on the work field. This device is used together with model JZF-9 or JZF-10 calibrator.

product features Product Characteristics

Working Principle

When measured piece Cx has partial discharge under testing voltage the circuit will have pulse current which get by the input unit. The pulse signal is amplified by front amplifier and the frequency band is chose by filter amplifier then been amplified to needed amplitude by the main amplifier. The pulse signal will be displayed on oscillograph screen. The pulse value is also sent to the pulse peak meter and displayed immediately. The time window unit chooses a working period of the pulse peak meter during each cycle of testing voltage and it increases the brightness of the relevant displaying area in this time. In this way it can avoid the disturbing of fixed phase.

Input discharge volume to the measured piece Cx through JZF series PD external calibrator adjust the fine adjusting knob till the displayed value is equal to the discharge volume the discharge can be read directly and conveniently on the meter without counting.

The testing voltmeter will have an over zero mark signal of testing voltage through the voltmeter resistance R and the zero mark pulse will be displayed on oscillograph screen. The testing voltage can be displayed on KV meter.

Product Parameters

Technical Parameters

Main specification

1 Measure channel：4-channel

2 Capacitance range of measured piece 6pF~250uF

3 Measuring sensitivity and Max. current（see table 1）

Table 1.

No.	Tuning capacitance range	Sensitivity (pC) (Un-balance circuit)	RMS of max. current
			(Un-balance circuit)	(Balance circuit)
1	0~25~100pF	0.02	30mA	0.25A
2	25~100~400pF	0.04	50mA	0.5A
3	100~400~1500pF	0.06	120mA	1A
4	400~1500~6000pF	0.1	0.25A	2A
5	1500~6000~25000pF	0.2	0.5A	4A
6	0.006~0.025~0.1uF	0.3	1A	8A
7	0.025~0.1~0.4uF	0.5	2A	15A
8	0.1~0.4~1.5uF	1	4A	30A
9	0.4~1.5~6.0uF	1.5	8A	60A
10	1.5~6.0~25uF	2.5	15A	120A
11	6.0~25~60uF	5	25A	200A
12	25~60~250uF	10	50A	300 A
7R	Resistor	0.5	2A	15A

4 Time base of ellipse scan

(1) Frequency 50 /60(inner) 100 150 200 400Hz

(2) Turn: 30º per grade total 360º

(3) display ways: ellipse——expand——beeline

(4) The high frequency time base ellipse can be adjusted to normal state by input voltage (10-250V) and the power is less than 1 VA. Auto-protecting function when overload

5 Displaying Unit

A rectangle oscillograph tube (124×104mm²) which has brightness and focus knobs.

6 Amplifier

(1) On low frequency 3dB fL: 10 20 40 KHz optional

(2) On high frequency 3dB fH: 80 200 300 KHz optional

(3) Gain adjusting: 6 grades of gross adjustment. Gain difference between grades is 20±1dB fine adjusting range >20dB

(4) Asymmetry of plus and minus pulse responding < 1dB

7 Time window

(1) Adjustable window width 15º~150º on 50/60Hz

(2) Rotatable window position 0º~170º

(3)Two windows can on/off respectively or simultaneously

8 Pulse peak meter

(1) Pointer meter with linear graduation. 0-100

(2) Pointer meter with logarithm graduation. 0-10-100

(3) Digital meter with 3.5 bits LED digital display 0-100

(4) Discharge magnitude linear deviation: <±10%

9 Zero mark system

(1) Made by inner zero mark generator it can change polarity and rotate 0-180º so it can correspond with the true zero mark which is made by high voltage resistor.

(2) The zero mark is corresponded with all ellipse scan frequency.

10 Power

AC Power: 230/400V; 60Hz; 3Phase

11 Work environment

Vicinity medium temperature is -5 ºC ~+45ºC

Air relative humidity is no more than 85%

Quality Keep Improving - Service Pursuing Perfection Pre-sales service commitment Provide professional consulting service; dedicated salesman and professional technical engineer to answer customer questions Ensure customer get the detailed information about the product in hand Reasonable price. Quotation stamped and confirmed by Manager

Welcome customers visit on-purchase service commitment The contract and the technical agreement to sign by both parties Being trustworthy, follow the requirements and ensure successful implementation of signed contracts and technical agreements Focus on communication, actively communicate with users, take notes of user’s questions and schedule, provide the necessary technical support. Move quick and efficient, professional on delivery, installation, debugging, training and others